AC Service & Repair
Scheduled servicing and same-day repair for split, ducted and central systems.
Learn moreElectrical
Fault finding, rewiring, distribution boards, lighting and sockets — tested properly and left safe, not just working.
Book Electrical
Send the details and we will price it before anyone comes out.
Fault finding, properly
Most electrical call-outs start the same way: something trips, gets reset, works for a while, then trips again. That cycle can continue for months, and each repetition is a circuit protection device doing exactly what it exists to do while the underlying fault stays unaddressed.
Finding the cause is a testing exercise, not a guessing one. Insulation resistance testing, earth continuity, and load measurement establish where the fault actually sits. That takes longer than swapping a breaker but it ends the problem instead of postponing it.
What we handle
- Fault finding — tripping circuits, intermittent failures and earth leakage.
- Distribution boards — replacement, upgrade and additional circuits.
- Rewiring, full or partial, including runs that have degraded in hot ceiling voids.
- Lighting — replacement, new positions, dimming and outdoor lighting.
- Sockets and switches, including additional points and USB outlets.
- Appliance circuits for ovens, hobs, water heaters and AC equipment.
- Outdoor and wet-area electrics, where moisture protection matters most.
Signs your electrics need attention
- Breakers that trip repeatedly, particularly under no unusual load.
- Warm or discoloured sockets, switches or plug tops.
- A burning or fishy smell near outlets or the board — treat this as urgent.
- Lights that flicker when other appliances start.
- Buzzing from switches, dimmers or the distribution board.
- Sockets that feel loose or where plugs no longer seat firmly.
Treat as urgent: a burning smell, visible scorching, or a socket hot to the touch. Switch that circuit off at the board and call rather than waiting for a convenient appointment. These are the conditions that precede fires.
Why choose us for electrical work
For testing rather than guessing
Faults get located with instruments and the results recorded. A circuit that “seems fine now” is not a diagnosis.
For work that stays safe
Connections torqued correctly, cable sized for the load, and terminations made properly. Most electrical failures we attend originate at a loose connection that heat-cycled its way apart over years.
Questions
Frequently asked questions
A breaker that trips repeatedly is doing its job — something is drawing more current than the circuit allows, or there is a leakage path to earth. The usual causes are a faulty appliance, moisture in an outdoor or bathroom circuit, or a circuit carrying more load than it was designed for. Resetting it repeatedly without finding the cause is the one response to avoid, because the breaker is the protection.
Unplug everything on the affected circuit, reset the breaker, then reconnect items one at a time leaving a few minutes between each. The appliance that trips it is your culprit. If the breaker trips with nothing connected at all, the fault is in the fixed wiring and needs testing rather than trial and error.
We test and document what we install, and provide a record of the results. Where work requires formal DEWA approval or inspection — new supply, main board changes, or load increases — that process runs through DEWA itself and we will tell you when your job falls into that category rather than after the work is done.
Heat and dust, mostly. Ceiling voids in Dubai run extremely hot, which shortens the life of drivers and transformers in LED fittings well before the LEDs themselves fail. Dust ingress into switches and sockets accounts for much of the rest. Fittings rated for higher ambient temperatures last considerably longer here.
In most cases, yes — replacing existing fittings or working through existing openings needs no new damage at all. New positions require cutting, but we plan runs to minimise it and make good afterwards. Where a ceiling is going to need patching and painting, we tell you that up front so it is part of the quote rather than a surprise.
It depends entirely on the existing circuit — its rating, its current load, and its cable size. Adding sockets to a circuit already near capacity creates exactly the overload condition that causes nuisance tripping and, over time, overheating at connections. We check the circuit before extending it rather than assuming there is headroom.
Related services
Often booked together
AC Replacement & Installation
Correctly sized replacement units, supplied and installed to spec.
Learn moreDuct Cleaning
Full ductwork decontamination to clear dust, damp and microbial growth.
Learn more